先导电磁阀

SDBB2132113A

双线圈模型

安装视图1

安装视图2

阀切角

 显示的引线版本

添加到RFQ修改零件回到选择器

规格书

标称系统压力（psi）4000

线圈数量双线圈

配置3路N.C.

洛姆速率2200

筛孔尺寸.004英寸标称

重量.20磅

工作温度：环境温度：-65ºF至275ºF

工作温度：流体：-65ºF至275ºF

泄漏：内部：大2 cc /分钟。在额定压力下

泄漏：外部：0 cc

测试液MIL-PRF-5606，MIL-PRF-83282

电气规格

电流消耗：70ºF（9.8瓦），28 Vdc时为0.35安

工作电压：32.2 Vdc

吸合电压：大18 Vdc在275ºF和对任一盘管的额定压力下

小压降：两个线圈在70ºF和额定压力下均能提供1.5 Vdc的电压

电阻：70ºF下为74-86欧姆

响应时间：吸合（在大工作压力下）：大0.015秒。

响应时间：跌落（大工作压力下）：0.035秒大

稳定温度：大285ºF。两个线圈都施加28 Vdc电压，悬浮在70ºF至110ºF的静止空气中，连续通电

绝缘电阻：小100兆欧。施加500 Vdc 60秒

介电强度：小1500 Vrms。在60 Hz下持续60秒

材料

身体和球座：15-5 PH CRES / AMS 5659

多次密封：聚酰胺酰亚胺/ AMS 3670

球形和大头针：440C CRES / AMS 5630

春季：302 CRES / AMS 5688

法兰，柱塞和盖：Si Iron BFM / ASTM-A867

滤网组件：304L CRES / ASTM A 666

梭芯：22-13-5 / AMS 5764

垫片：302 CRES / ASTM A 666

轴：440C CRES / AMS-Q-S-763

固定器：2024 T-351 AL / Q-A-225 / 6

固定环：302 CRES / ASTM A313 / A313M

线圈：铜磁线/ NEMA MW1000

引线：22 AWG / SAE AS22759 / 11-22

分隔符：Aramid / MIL-I-24204

收缩管：MIL-I-23053 / 8和/ 12

绝缘胶带：Kapton，聚酰亚胺/ ASTM D5213

焊接：Sb05A / J-STD-006

钎焊：AMS 4774

灌封胶：Stycast 2762FT，Catalyst 17

正面电气连接导线版本

完

Cres零件：钝化

软磁材料：镍板/ AMS 2404

固定器：阳极氧化/ MIL-A-8625 II型

安装/提取

备用多密封件零件编号SDBB2130108A

推荐安装扭矩25 ft-lbs

Piloting Solenoid Valve SDBB2132113A   Dual Coil Model Installation View 1 Installation View 2 Valve Cutaway  Leadwire Version Shown

SPECIFICATIONS Nominal System Pressure (psi) 4000 Number of Coils Dual Coil Configuration 3-way N.C. Lohm Rate 2200 Screen Hole Size .004 inches nominal Weight .20 lbs. Max. Operating Temperature: Ambient: -65ºF to 275ºF Operating Temperature: Fluid: -65ºF to 275ºF Leakage: Internal: 2 cc/minute max. at rated pressure Leakage: External: 0 cc Test Fluid MIL-PRF-5606, MIL-PRF-83282 ELECTRICAL SPECIFICATIONS Current Drain: 0.35 amps at 28 Vdc at 70ºF (9.8 Watts) Max. Operating Voltage: 32.2 Vdc Pull-In Voltage: 18 Vdc max. at 275ºF and rated pressure to either coil Minimum Drop Out Voltage: Both coils energized 1.5 Vdc at 70ºF and rated pressure Resistance: 74-86 Ohms at 70ºF Response Time: Pull-In (at max. working pressure): 0.015 seconds max. Response Time: Drop-out (at max. working pressure): 0.035 seconds max. Stabilization Temperature: 285ºF max. with 28 Vdc applied to both coils, suspended in 70ºF to 110ºF still air, continuously energized Insulation Resistance: 100 Megohms min. with 500 Vdc applied for 60 seconds Dielectric Strength: 1500 Vrms min. at 60 Hz for 60 seconds MATERIALS Body and Ball Seat: 15-5 PH CRES/AMS 5659 Multi-Seal: Polyamide-Imide/AMS 3670 Ball and Pin: 440C CRES/AMS 5630 Spring: 302 CRES/AMS 5688 Flanges, Plungers and Cover: Si Iron BFM/ASTM-A867 Filter Screen Assy: 304L CRES/ASTM A 666 Bobbin: 22-13-5/AMS 5764 Spacer: 302 CRES/ASTM A 666 Shaft: 440C CRES/AMS-Q -S-763 Retainer: 2024 T-351 AL/Q -A-225/6 Retaining Ring: 302 CRES/ASTM A313/A313M Coil: Copper Magnet Wire/NEMA MW1000 Lead Wire: 22 AWG/SAE AS22759/11-22 Separator: Aramid/MIL-I-24204 Shrink Tube: MIL-I-23053/8 & /12 Insulation Tape: Kapton, Polyimide/ASTM D5213 Solder: Sb05A/J-STD-006 Braze: AMS 4774 Potting Compound: Stycast 2762FT, Catalyst 17 Front Electrical Connection Lead Wire Version FINISH Cres Parts: Passivated Soft Magnetic Material: Nickel Plate/AMS 2404 Retainer: Anodize/MIL-A-8625 Type II INSTALLATION / EXTRACTION Replacement Multi-Seal Part Number SDBB2130108A Recommended Installation Torque 25 ft-lbs