PROSOFT PLX31-EIP-PND通信?？橄只踅樯?/h3>

阅读：482        发布时间：2023-8-15

PROSOFT PLX31-EIP-PND通信模块

PROSOFT PLX31-EIP-PND通信?？?/span>

※※※ 深圳市扎克贸易有限公司

※※※ 张瑞 188-24-24-3080（V同）

EtherNet/IP™ to PROFINET® IO Device Gateway

PLX31-EIP-PND

The EtherNet/IP™ to PROFINET® IO Device (slave) gateway offers bi-directional data transfers between EtherNet/IP™ controllers and a PROFINET® IO controller. The EtherNet/IP™ Driver supports I/O connections for guaranteed data delivery or Message instructions to send data to/from the PACs. The gateway supports 1440 bytes of input data and 1440 bytes of output data for larger applications.

In addition, the gateway’s multiple I/O connections, allow you to set different RPIs for control data and module diagnostics, enabling you to optimize your Ethernet bandwidth.

A conformal coating option is available for this product.

Specifications

Number of Class 3 Server Connections	5
Supported PLC Types	PLC2, PLC5, SLC, CLX, CMPLX
Supported Message Types	PCCC and CIP
Number of Class 3 Client Connections	Connected - 2 Unconnected - 1
Number of Class 1 I/O Connections	8
Max I/O connection sizeIn/Out	496/496 bytes
Max RPI time	10 ms per connection
CIP Services Supported	0x4C - CIP Data Table Read 0x4D - CIP Data Table Write
Command List	Support for 100 commands per Client, each configurable  for command type, IP address, register to/from addressing and word/bit count.
Command Sets	PLC-2/PLC-3/PLC5 Basic Command Set PLC5 Binary Command Set PLC5 ASCII Command Set SLC500 Command Set

Hardware Specifications

Power Supply	24 VDC nominal 10 to 36 VDC allowed Positive, Negative, GND Terminals
Current Load	24 VDC nominal @ 300 mA 10 to 36 VDC @ 610 mA maximum
Operating Temperature	-25°C to 70°C (-13°F to 158°F)
Storage Temperature	-40°C to 80°C (-40°F to 176°F)
Shock	IEC 60068-2-27; 15G @ 11ms, 3-Axis (Operational) IEC 60068-2-27; 30G @ 18ms, 3-Axis (Non-Operational)
Vibration	IEC 60068-2-6; 5G @ 10 to 150 Hz
Relative Humidity	5% to 95% RH with no condensation
Dimensions (H x W x D)	5.38 x 1.99 x 4.38 in 13.67 x 5.05 x 11.13 cm
LED Indicators	Configuration (CFG), Error (ERR), Power (PWR),  Hardware Fault (FLT), Network Status (NS),  EtherNet/IP™ Class I or Class III Connection Status  (EtherNet/IP Only) Module Status (MS), ModuleConfiguration Status (EtherNet/IP Only) Ethernet Communication Port Link/Activity, and 100 mbit
Ethernet Port	10/100Mbit half-duplex RJ45 Connector Electrical Isolation 1500 Vrms at 50 to 60 Hz for 60 seconds, applied as specified in section 5.3.2 of IEC 60950: 1991 Ethernet Broadcast Storm Resiliency is less than or equal to 5000 [ARP] frames-per-second and less than or equal to 5 minutes duration
Shipped With Each Unit	2.5 mm screwdriver J180 Power Connector

上一篇

ProSoft PLX31-EIP-MBS?？榻樯?/span>

下一篇

ProSoft PLX31-EIP-MBTCP通信模块介绍