日本YUKEN座阀型电磁换向阀型号规格

The use of the low viscosity hydraulic fluids reduces the pressure loss
which can a rise from the passage resistance of the hydraulic fluids, leading to the system energy saving
高响应高性由于这些阀是提升型，
所以没有重叠，可以实现高响应。
This makes it possible to use these valves in combination with 01 Series Modular Valves.
This is the leakage towards "T" port in A port block at "P" port pressure 14 MPa (2030 PSI).
 使用低粘度液压流体减少了压力损失，
这可以从液压流体的通道阻力上升，导致系统节能。
These are Solenoid Operated Directional Valves of No Leak Type developed with the aim of responding the demand of the a ge including energy saving. 
Because these valves are of no leak type they allow the low viscosity hydraulic fluids to be used
否则可能会导致故障的破坏并缩短阀门的使用寿命。
 请保持NAS 1638Grade 12内的污染程度。
使用25μm或更细的线路滤波器。
Recommended Viscosity and Oil Temperatures 2  Viscosity ranging between 15 - 400 mm /s (77 - 1800 SSU). 
Oil temperatures between -15/+70°C (5 - 158°F).  Use hydraulic fluids which satisfy the recommended viscosity and oil temperatures given above.
 同时，液压锁消除。
不采用泄漏片式密封，内部泄漏大大降低。
ISO Comformant安装面由于安装面符合ISO 4401-AB-03-4-A，
因此与常规阀门可互换。
这使得可以将这些阀门与01系列模块阀组合使用。
这是在“P”端口压力14 MPa（2030 PSI）下A端口块中“T”端口的泄漏。
 Control of Contamination Due caution must be paid to maintaining control over contamination of the hydraulic fluids
 which may otherwise lead to breakdowns and shorten the life of the valves.
这些是为了应对包括节能的需求而开发的无泄漏型电磁操作方向阀。
因为这些阀门是没有泄漏的，所以它们允许低粘度液压油

日本YUKEN座阀型电磁换向阀型号规格
No Leak Sheet type seal has been adopted and internal leak is greatly reduced.
这是在“P”端口压力14 MPa（2030 PSI）下，A•B端口块中的“T”端口泄漏。
High Response High Reliability Because these valves are of poppet type, there is no overlap,
 high response can be achieved.  At the same time, hydraulic lock is eliminated.                        
提示类型  电磁操作方向阀DSLG-01-3-C / O
流体类型可以使用表中列出的任何类型的液压油。
ISO Comformant Mounting Surface Because the mounting surface conforms to ISO 4401-AB-03-4-A,
This is the leakage towards "T" port in A•B  port block at "P" port pressure 14 MPa (2030 PSI).
的粘度和油温2粘度范围在15 - 400 mm / s（77 - 1800 SSU）之间。
油温在-15 / + 70°C（5 - 158°F）之间。
 使用满足上述给出的粘度和油温的液压油。
污染控制必须注意保持对液压油污染的控制，
安装螺栓包括下表中的四个内六角头螺钉。
以及由于压力油内部泄漏太多而不能被传统的阀芯型换向阀使用的回路结构。
there i s an interchangeability with the conventional valves.
 Please maintain the degree of contamination within NAS 1638Grade 12.  Use 25 µm or finer line filter.
石油基础油合成液含水液体
使用与ISO VG 32或VG 46相当的流体。使用磷酸酯或多元醇酯液。
当使用磷酸酯流体时，需要使用特殊密封（氟橡胶），
使用前缀“F-”型号。 使用水 - 液体。
子板可用。 从上表中子板型号。
当不使用子板时，安装表面应具有良的加工精加工。
 as well as the circuit construction which cannot be used by the conventional spool type directional valves because of too much internal leak of pressure oil.