122-01POLYIMIDE COATING聚酰亚胺涂层

说明：122-01是单组分、电绝缘、耐溶剂、聚酰亚胺基、粘合剂

以及适于通过丝网印刷、浸渍和注射器分配应用的涂层。这个产品是为

装配电气和电子部件。固化计划允许快速处理和

粘合剂在高温下具有优异的热稳定性和附着力。122-01是CMI的未填充版本

110-19。

典型固化特性：

稠度光滑膏

玻璃变压器。临时雇员。（摄氏度）>250

水解稳定性优异

有效温度范围（℃）-55至+230

热稳定性（摄氏度）达到325

T-抗剪强度（psi）>1500

建议的处理和固化：122-01已准备好可供使用。在表面涂上粘合剂

用手工和/或自动方法粘合和装配。施加轻微压力以确保表面良好配合

以及菲力的形成。在200℃下固化1小时后，大多数应用的性能。良好性能

通过在150°C至210°C的温度下固化，在多种基底上获得。小

固化时间和温度，以确保180°C下的耐溶剂性为1小时。建议终用户

通过实验确定适合个人应用的温度和时间。

储存：保质期：23°C或更低温度下储存1年。在更高的温度下储存可以提高树脂的性能。

**请注意：122-01在储存过程中可能结晶。要重新熔化晶体，请将其放在温水浴中或热的

在90°C–100°C下加热，直到晶体溶解。不要无人看管。融化晶体的时间是

取决于质量。

安全和操作：在通风良好的情况下使用。远离火花和明火。避免长时间

接触皮肤和吸入蒸汽。用肥皂和水清洗皮肤。

122-01POLYIMIDE COATING聚酰亚胺涂层

122-01
POLYIMIDE ADHESIVE / COATING
DESCRIPTION: 122-01 is a single component, electrically insulating, solvent resistant, polyimide based, adhesive
and coating suitable for application by screen-printing, dipping and syringe dispensing. This product is designed for
assembling electrical and electronic components. The cure schedule allows for rapid processing and the resulting
bond exhibits excellent thermal stability and adhesion at high temperatures. 122-01 is an unfilled version of CMI
110-19.
TYPICAL CURED PROPERTIES:

Consistency Smooth Paste
 Glass Trans. Temp. (°C) > 250
 Hydrolytic Stability Excellent
 Useful Temperature Range (°C) -55 to +230
 Thermal Stability (°C) Good to 325
 T-Shear Strength (psi) >1500
SUGGESTED HANDLING & CURING: 122-01 is ready to use as supplied. Apply adhesive to surface to be
bonded by hand and/or automatic method and assemble. Apply slight pressure to assure good mating of surfaces
and formation of filet. Best properties for most applications result when cured for 1 hour at 200°C. Good properties
are obtained on a variety of substrates by curing at temperatures ranging from 150°C to 210°C. The minimum
cure time and temperature to assure solvent resistance is one hour at 180°C. End user is advised to
experimentally determine temperature and time best suited for individual applications.
STORAGE: Shelf Life: 1 year when stored at 23°C or less. Storing at higher temperatures may advance the resin.
** Please note: 122-01 may crystallize during storage. To re-melt crystals, place in a warm water bath or on a hot
plate at 90°C – 100°C. Heat only until crystals dissolve. Do not leave unattended. Time to melt the crystals will be
dependent upon the mass.
SAFETY & HANDLING: Use with adequate ventilation. Keep away from sparks and open flames. Avoid prolonged
contact with skin and breathing of vapors. Wash with soap and water to remove from skin.